3 4.3 5 5.7 5.8 7.4 8.1 8.2 AQ Models Aquamatic Models B Models D Models D3 Series DP A Models DP B Models DP C Models DPX Models MD Series Penta 100 Penta 230 Penta 250 Penta 251 Penta 270 Penta 280 Penta 285 Penta 290 Penta 500 SP A Models SP C Models TAD Series TMD / TAMD. Kingdom come deliverance console commands spawn npc. This new in-line six-cylinder diesel from DDC/Volvo packs a wallop and is coming your way soon. Slated for introduction at the 1998 Ft. Lauderdale International Boat Show, DDC/Volvo Penta's new 7-liter Series 74 EDC in-line six-cylinder diesel is said to develop 480 crankshaft horsepower at 2600 rpm. Trainz simulator 12 free download pc.
Hi Carver owners,I have a 2002 466MY with twin Volvo TAMD 74P-As - although the blocks say TAMD75P - can't work that one out since a serialisation search confirms they are 74P-As. Anyway, these have an EDC system installed.
I had a mechanic fix a problem with the starboard forward not engaging. Dammit he showed me how he fixed this but I cannot recall exactly what he did. My problem now though is that the port forward thrust is taking 30 seconds or so before it engages. Volvo Tamd 74 Edc Problems
Would anyone have a clue on how I can fix this? Port astern and the starboard ahead and astern thrusts have the normal one second delay before engaging the props.
Unfortunately where the vessel is now there are no VP certified mechanics. So any help or a point in the right direction would be well received.
Raymond
Volvo Penta Tamd74edc Manual
Hello All. Great forum! I'm brand new to this forum and I'm impressed. I'm hoping someone on here can help with my EDC issue. Here's what's happening:
Took the boat out many times this summer. She ran great. Summer prior (2018) I had a very high powered stereo hooked up to my 2 starter batteries in my 2003 Regal 4260 Express. My port side would go dead and I'd only have starboard to dock the boat. No forward, no reverse. I discovered one of the 3 breakers in the control box mounted on the side of the engine would pop. I'd push it back in and the controls would start working again. Ultimately, I replaced the breaker and port side has run flawlessly. Fast forward to summer of 2019. Startboard side starts acting up. Nothing at all in forward. Reverse was perfect. I suspect stereo hooked to engine batteries was interfering with EDC's. Pulled stereo off batteries, take her for a run, she runs perfectly. Summer of 2020; all is great until October when I take her for a run. She would pull hard until almost on plane, then just drop into neutral. Engine would rev, but no forward thrust. Reverse is perfect. Oil sample shows 358ppm for copper, 98ppm for aluminum, which Wix says is abnormal. Not severe which is their worst grade. I'm not sure if when the engine was pulling onto plane, then went into neutral and just revved, did it slip the clutch by possibly the solenoid being partially open and increased the level of copper? I'm trying to figure out if I have an electrical problem and or if the trans is in need of a rebuild. I swapped solenoid from forward to reverse on trans and nothing changed. Figured if seloniod was bad, I'h have no reverse with the swap. Thanks for anyones help!
Took the boat out many times this summer. She ran great. Summer prior (2018) I had a very high powered stereo hooked up to my 2 starter batteries in my 2003 Regal 4260 Express. My port side would go dead and I'd only have starboard to dock the boat. No forward, no reverse. I discovered one of the 3 breakers in the control box mounted on the side of the engine would pop. I'd push it back in and the controls would start working again. Ultimately, I replaced the breaker and port side has run flawlessly. Fast forward to summer of 2019. Startboard side starts acting up. Nothing at all in forward. Reverse was perfect. I suspect stereo hooked to engine batteries was interfering with EDC's. Pulled stereo off batteries, take her for a run, she runs perfectly. Summer of 2020; all is great until October when I take her for a run. She would pull hard until almost on plane, then just drop into neutral. Engine would rev, but no forward thrust. Reverse is perfect. Oil sample shows 358ppm for copper, 98ppm for aluminum, which Wix says is abnormal. Not severe which is their worst grade. I'm not sure if when the engine was pulling onto plane, then went into neutral and just revved, did it slip the clutch by possibly the solenoid being partially open and increased the level of copper? I'm trying to figure out if I have an electrical problem and or if the trans is in need of a rebuild. I swapped solenoid from forward to reverse on trans and nothing changed. Figured if seloniod was bad, I'h have no reverse with the swap. Thanks for anyones help!